Correct me if I am wrong but ice makers are as important as fridge and freezers. You cannot deny the working of ice makers because trust me, they come in handy in difficult situations. Well, there are some people who get their appliances fixed as soon as they feel like they are not working fine. On the other hand, some people don’t get their appliances fixed until they completely stop working.
Today, I will be discussing about the problems associated with Kenmore Refrigerator 795 ice maker. Well, not just the problems but I will also be mentioning the relevant fixes with them. All you need to do is keep following this article till the end so you can easily apply the fixes.
Kenmore Refrigerator 795 Ice Maker Problems
Following are the problems associated with the Kenmore Refrigerator Ice Maker.
- Faulty Control Board
- Setting Freezer Temperature High
- Defective Water Inlet Valve
- Faulty Ice Maker Assembly
- Frozen Fill Tube
- Low Water Pressure
- Ice Maker being turned OFF
- Frozen Fill Tube
- Stuck Dispenser Door
- Faulty Door Switch
- Clogged Fill Tube Heater
- Clogged Water Filters
Troubleshooting Guide
Now that you have become familiar with the problems, it is time to talk about the troubleshooting. Make sure to follow each and every step properly in order to avoid future inconvenience.
1. Faulty Control Board
The main control board is responsible for sending the voltage to the ice maker. In case the control board becomes defective, the ice maker will also not work at all. For your relief, you can check the board for possible damages or shorted components. Moreover, you can also use a multimeter in order to determine whether the voltage is reaching the ice maker or not. You can also take help from the refrigerator’s wiring diagram.
2. Setting Freezer Temperature High
If you have set the freezer temperature above 10 degrees Fahrenheit i.e. -12C, then unfortunately the refrigerator will not produce the ice cubes properly. The ideal freezer temperature should be between 0 – 5 degrees Fahrenheit. But if you want to set the freezer temperature high then all you need to do is keep the condenser coils clear and the fan should be working properly. Moreover, you can also check the evaporator coils for possible ice-buildup. The defrost system will most likely fail if the evaporator coils are frosted over.
3. Defective Water Inlet Valve
Water inlet valve is responsible for supplying water to the ice maker and dispenser. This valve is controlled electrically. If the water inlet valve has become defective or the water pressure is not enough then the water will not flow properly. Consequently, there will be no ice cubes produced. The water pressure should be at least 20 psi for the water valve to work properly. If you think that the water pressure is sufficient then all you need to do is take a multimeter and check the water inlet valve. In case you witness no continuity, you need to make a quick replacement.
4. Faulty Ice Maker Assembly
Another important component of your refrigerator is the ice maker assembly. Unfortunately, ice maker components are not sold separately so you need to buy the entire ice maker assembly. But it is indeed a big investment and you should check other components like the water line, water inlet valve and fan before replacing the whole assembly unit. If these components are working fine and there is nothing wrong with the freezer temperature then definitely you need to replace the ice maker assembly.
5. Frozen Fill Tube
If the water pressure is insufficient or the water valve has become faulty then the fill tube of your ice maker will probably become clogged with ice. This clogging will prevent the water from entering the ice maker tray. Before thawing out the frozen fill tube it is important to check the water pressure as well as the proper functioning of the inlet valve. If you see that the fill tube is damaged then you need to replace it with a new one.
6. Low Water Pressure
Carefully inspect the water pressure level. The pressure needed by your water inlet valve is around 20 psi. Make sure it is receiving the same pressure because only then the ice maker and water inlet valve will work properly.
7. Ice Maker Being Turned OFF
You can also make this common mistake of assuming that your ice maker is ON when in reality it is OFF. Ensure that the paddle and arm of your ice maker are able to move freely without any obstruction. If you own an in-door ice dispensing model then make sure the indicator light stays on when the door is opened.
8. Frozen Fill Tube
As mentioned before, if the inlet valve and water pressure are working improperly then as a result the fill tube will become clogged. You can use a hair dryer to thaw out the frozen fill tube. But also make sure that the inlet valve is not defective and the water pressure is sufficient.
9. Stuck Dispenser Door
After the ice is dispensed, the dispenser door will shut the door by using its closing mechanism. If the door remains opened then the warm air will enter the fridge and will restrict the ice maker compartment from producing ice cubes. Remove all the potential obstacles that are keeping the dispenser door from closing.
10. Faulty Door Switch
The purpose of a door switch is that it turns off the ice and water dispenser when the refrigerator door is open. In case the door switch fails, the dispenser will not turn ON. Use a multimeter in order to find out whether the door switch has become faulty or not. If the door switch is faulty then you need to replace it.
11. Clogged Fill Tube Heater
The fill tube heater keeps the fill tube warm so that the ice buildup doesn’t occur. If the heater becomes clogged or damaged then the fill tube will be covered in ice buildup and as a result water will not flow to the ice maker.
12. Clogged Water Filters
Clogged or blocked water filters will restrict the water to flow to the dispenser. As a result, the ice maker will not work properly. You need to replace the water filters after every 6 months to maintain its quality.
Also Check More Refrigerator:
Refrigerator Light Comes ON but Nothing Else [Fixation 2024]
Kenmore Refrigerator Ice Maker Troubleshooting [Method 2024]
GE Profile Refrigerator Ice Maker Reset [Fixations 2024]
Fridge Making Noise When Door Closed [9 Fixation 2024]
Frigidaire Refrigerator Water Dispenser Slow [Fixation 2024]
Whirlpool Refrigerator Water Dispenser not Working [7 Fixes]
Frequently Asked Questions
Q – How do I reset my ice maker?
A – Find the “Lock” and “Light” buttons on your unit. Once found, keep them pressed simultaneously for around 3 seconds. After this, you will hear a chime and the display will change indicating a reset.
Q – How long do Kenmore ice makers last?
A – Kenmore ice makers last for 4 – 5 years if you are using them continuously.
Q – Where is the reset button on an ice maker?
A – Mostly the reset buttons on ice makers are usually located at the bottom. But in some models the reset buttons are located at the top as well.
Concluding Thoughts
The failure of a Kenmore refrigerator ice maker to produce ice might be attributed to various issues. There could be a blockage in the water flow caused by a kinked water line, a jammed or damaged ice maker, or a malfunctioning or clogged water inlet valve.