Maytag is one of the best brands considered among people. People say that Maytag washers are huge life savers. Due to the hype, people will literally consider buying this washer no matter what. But if you are thinking that these washers will never stop working then you might be wrong here. Every electrical appliance is meant to experience some technical faults and glitches. So remove this thought from your mind that if you buy any appliance from a popular brand then you won’t face any issue ever.
Maytag washer users often complain that their washer fills with water but then eventually stops. It is considered a common issue nowadays. Undoubtedly, this issue is actually frustrating. No one would want their electrical appliance to stop working out of nowhere. Gladly, I am here to help! In this article I will be navigating through the same issue so make sure you stay with me till the end of this article.
Maytag Washer Fills with Water then Stops – Reasons and Fixes
Well, as an expert I might not have dealt with all the issues but I have done sufficient research on every possibility. Make sure you follow the exact same steps as stated by me in this section of the article.
1. Open Lid
The most common reason why your Maytag washer eventually stops after filling with water is an open lid. An open lid will only allow the washer to get filled with water but it will restrict its working. If this is the reason then check the below mentioned possibilities.
- The lid might not be shut firmly
- There might be some obstacles present between the lid
- Presence of a faulty lid switch
Solution
Close the lid properly and make sure there aren’t any obstacles present between the lid. The sensors present in the Maytag washer will detect an open lid and won’t work until and unless the lid is closed properly. Also check the lid switch, if it has become faulty then you need to get it replaced as soon as possible.
2. Soak Mode Activation
Maytag washers come with a “Soak Mode”. If this mode is enabled then your washer will stop after filling with water. The purpose of this mode is that it holds the clothes for some time in order to soak them up. 10-15 minutes is the total duration of this process. If there is no other problem with your washer then of course the washer will resume its normal operations.
Solution
You can either wait for the soak cycle to complete or you can interrupt the cycle by pressing “Cancel” on the washer.
3. Stuck Objects
In case there are stuck objects present in the drum then the washer will eventually stop filling with water. Reason? Well, the sensors will sense the presence of these stuck objects and will interrupt the normal working of the washer.
Solution
After removing all the obstructions from the drum, restart the washer. In addition to this, check the drum lock as well and in case it has become faulty then make sure to get it replaced with a new one.
4. Clogged Pump
Your washer will refuse to fill water if the pump or hose has been clogged. You need to inspect both these things for clogging. The water fill-up process gets highly affected due to clogged hoses and pumps.
Solution
Clean the clogged hose or pump of the washer if they have been clogged. Remove all possible twists and kinks in the drain hose by stretching them out. After doing this, the drainage system of your washer will be improved.
5. Faulty Cycle Selector
Having a faulty cycle selector means that the washer will refuse to work or operate. In this case, the washer will not fill any water and it will also refuse to work. So now you have two issues to deal with. If you witness the motor not running properly or the drum is not spinning then it might be due to the presence of a damaged cycle selector.
Solution
Take a multimeter and check the working of the cycle selector. If no continuity is shown then you need to make a quick replacement otherwise things might get worse.
6. Defective Drive Belt
In case the drive belt of your washer is tight, broken or loose then it will not be able to make the motor run. As a result, all the operations will be paused.
Solution
What you need to do is replace the washer belt with a new one. Don’t try to carry out the process on your own as it is complex. Make sure to contact a technician to get the job done.
7. Burnt Heater
Heater is one of the important elements of the washer. The washer’s fill up process will start as soon as the heater is turned ON. Sensors present in the washer will make the motor run after a specific temperature is reached. But this will only happen as long as the heater is working fine.
Solution
Check the heater first. If it is damaged then you need to replace it with a new one.
8. Defective Pressure Switch
Pressure switch is used to regulate the water level in the washer. If it becomes faulty then there would be nothing to control the water level. Moreover, the motor will also not get any power in case the pressure switch has become defective.
Solution
Take a multimeter and check the pressure switch. In case of no continuity, replace the defective pressure switch with a new one.
9. Faulty Timer
The working of the washer motor depends heavily on the timer. Washer might not fill properly due to the presence of a faulty timer. You can also say that the motor receives the working-signal from the timer.
Solution
The solution of this problem is a bit tricky so make sure you contact a technician to get the job done.
10. Defective Control Module
If you have checked all the above possibilities and you found no luck then make sure to check the control module. The control module is considered to be the brain of your washer. All the activities are controlled by this component. If it becomes faulty then the overall working of your washer will be greatly affected.
Solution
Call an electrician and have your control module replaced with a new one. Don’t try to fix the existing module as it can bring future inconveniences.
Frequently Asked Questions
Q – Why is my Maytag washer filling with water?
A – If your washer keeps filling with water then it means the water inlet valve is opened. It might be damaged as well so make sure to turn OFF the water supply in order to avoid excessive filling.
Q – Where is the Maytag reset button?
A – Unfortunately, Maytag washers don’t have a reset button. But you can perform a reset by pressing different buttons in combination.
Q – What is auto-fill on a Maytag washer?
A – Auto-fill or auto-sensing cycles sense how much water is actually required based on the fills and load size.
Wrap Up
There are a total of 10 potential causes for your washer’s issues. These are the most widely accepted reasons, though there are many others. Your only task now is to identify the true cause and implement a suitable remedy to address it.