Maytag Bravos is the only brand that people usually go for whenever they want to have the best appliances. Keep this thing in mind that whenever you are choosing Maytag Bravos then there shouldn’t be any doubt left in your mind. You are already choosing the best. However, there are always some problems that your appliances will face no matter what the brand is. Today, I will be explicitly talking about Maytag Bravos XL washer. I will be covering all the troubleshooting methods which are related to it. Make sure to give this article a proper read.
Maytag Bravos XL Washer Troubleshooting and Fixes
In this section of the article I will be talking about Maytag Bravos XL washer problems along with their fixes. Make sure to follow this section thoroughly.
1. Lid Lock Issues
The most common problem faced by the users is when they experience lid lock issues. Lid locks are usually present for the safety purpose. As long as the lock is not closed properly, the machine will not operate no matter how much you try to use it. The normal functioning of your unit will be affected once the lock starts causing trouble.
Solution
After making a confirmation regarding the presence of a defective lid lock, it is better to get it replaced without wasting any further time. You can also contact an expert to get the job done.
2. Error Codes
You will know that your washer is malfunctioning once there are error codes present on the washer’s display panel. This is one of the best features that Maytag Bravos Washers offer to their users. Through error codes, one can gather information regarding the diagnosis of the problem faced by the washer.
Solution
Note down the error code that you are encountering. After doing this, break down the code in order to interpret its meaning. Once done, use the user manual for further troubleshooting. Most of the errors are related to temperature sensor, internal components and draining.
3. Unbalanced Load
Unbalanced load in the washer drum can create many problems for you. In case this happens then get ready to experience excessive vibration and loud noises. Your washer can also stop mid-cycle due to an unbalanced load.
Solution
Take out all the laundry and distribute it evenly this time. Make sure to fill the drum according to its capacity. Moreover, inspect the water-levelling and sort your clothes by weight.
4. Washer not Filled with Water
Washer not filling with water can greatly affect the cleaning of your clothes. As a result, the clothes will still remain dirty even after a complete wash-cycle.
Solution
Check the valves for both hot and cold water, make sure they are fully opened in order for a proper water flow. Next, inspect the hose for possible kinks and blockages. If found, make sure to remove them as soon as possible. In case the hose is damaged, get it replaced with a new one. Hoses can also become clogged, you can unclog them using a brush. Last but not the least, check the water inlet valve, if it is damaged then you will have to replace it as well.
5. Washer not Draining Properly
Personally, I hate wet clothes. Especially when I receive them after a wash cycle. This happens due to poor draining of your washer. Well, there are many reasons that can contribute to this particular problem.
Solution
The easiest solution for this problem would be to clean the drain pump filters. Moreover, examine the drain hose as well.
6. Excessive Vibration and Loud Noises
Experiencing loud noises and excessive vibration from your washer could get really annoying for you. You need to get this issue resolved before it becomes a real problem for you. However, this issue might occur due to an unbalanced load, faulty tub bearing and defective suspension rods.
Solution
To solve the unbalanced load issue, make sure to redistribute the laundry evenly. After this, check the suspension rods because they might wear out due to continuous working. If found faulty, then get them replaced as soon as possible. Lastly, check the tub bearing as it can also cause the drum to produce unusual sounds.
7. Washer not Spinning
Maytag washer not spinning clothes for you can become a real problem. You will have your clothes dirty and dry at the end of each wash cycle. It might happen due to defective lid switch, damaged drive belt and malfunctioning motor.
Solution
The drive belt can become faulty due to continuous working. If you find the belt to be faulty then make sure to get it replaced with a new one. In case the motor’s engine has become faulty, call a technician to get the job done. Ensure the proper working of the lid switch as well. The washer will work only if the lid is closed properly.
8. Water Leakage
A water leakage problem can become a real problem for you and your washer as well. It might occur at different phases of the washing but the potential reasons for this problem are: a loose hose, damaged door seal and a faulty water pump.
Solution
Check the gasket thoroughly and look for possible damages. If you find any damage then make sure to replace it quickly. The seal should be cleaned and debris free. In case the above two things are in a clear zone then check the water pump. Call a technician and have him look at it.
9. Detergent Dispenser Issues
Detergent dispenser issues can affect the cleanliness of your clothes. The clothes will not be cleaned properly due to a faulty dispenser motor and clogged dispenser.
Solution
Dispenser motor is an important component of your washer. Make sure to contact a technician so he can check the motor properly. If any issue is found then you can simply ask the technician to have the motor replaced with a new one.
10. Washer Stops Mid Cycle
If your washer is stopping mid cycle then it means you will have clothes which are half soaked in water and detergent. This situation must be really frustrating for you, right? Well this problem occurs due to the reasons like faulty door lock, overloaded washer and overheating motor.
Solution
Always fill the washer drum according to its capacity. If you try to fill the drum beyond its capacity then you will face other issues as well. Moreover, if the motor gets overheated then the washer will definitely stop mid-cycle. After the motor cools down, the working of the washer will be resumed.
Also Check More Washer:
LG Direct Drive Washing Machine Problems [10 Solutions 2024]
Maytag Washer Fills with Water Then Stops Reasons 2024
How to Reset Maytag Bravos Washer [4 New Method 2024]
GE Washer Not Spinning Clothes Dry [6 Fixations]
Kenmore Washer Not Spinning Clothes Dry [6 Fixation 2024]
GE vs Samsung Washer [Comparison Which One Is Better 2024]
GE vs LG Washer [Comparison Which One is Better?] 2024
Maytag Bravos MCT Washer Problems [Fixation 2024]
GE vs Whirlpool Washing Machine [Which One Is Best in 2024]
Washing Machine Drain Pipe Height [Explained Correct 2024]
Frequently Asked Questions
Q – How do I reset my Maytag Bravos XL washer?
A – If you want to reset your Maytag Bravos XL washer then all you need to do is unplug the main power cord and wait for around 5-10 minutes. After this duration, plug back the power cord into the socket and run a test cycle to check whether the washer is working properly or not.
Q – Why won’t my Maytag washer start the cycle?
A – Your Maytag washer might not start the cycle due to a faulty user interface, jammed door lock assembly or a malfunctioning electronic control board. Look into these problems and try to have them resolved.
Q – How to fix F5 code on Maytag Bravos XL washer?
A – If you want to clear the F5 code from your Maytag Bravos XL washer then you need to unplug your washer for 10 straight minutes. Doing this will do the trick for you.
The End
Overall, there are some problems with every device that a customer will eventually encounter. I’ve walked you through potential issues and how to resolve them. The next step would be to identify the cause of your washer’s issue and apply a suitable remedy.