Nowadays, everything has gone through a major revolution. Let it be the washers or any other electrical appliance, almost everything is currently built on the latest technology. People say that with difficulty comes ease and vice versa. Where the manufacturers have provided you with the latest technology, the problems have become more severe and difficult to solve. Today, I will be discussing Maytag Bravos MCT Washer Problems along with their solution. Stay with me till the end in order to find out more.
Maytag Bravos MCT Washer Problems – Reasons and Fixes
In this section I will be enlightening you regarding various problems which Maytag Bravos MCT washer users face. Along with this, I will also be discussing the fixes so you don’t have to consult any other source for problem solving.
1. Washer Won’t Start
If your Maytag Bravos MCT washer doesn’t start then it can be due to the following reasons.
- Blown Thermal Fuse
Most definitely, the thermal fuse will be blown when the washer has become overheated. You need to check the thermal fuse using a multimeter. If there is no continuity shown then it means it has gone defective and you need to replace it as soon as possible.
- Dead Control Board
If there are no potential issues with the thermal fuse or lid lock of your washer then do check the control board. Unfortunately, there is no solution other than replacing it.
- Defective Lid Lock
Having a defective lid lock means that the machine will not be able to run smoothly and normally. You need to test it with a multimeter and if it comes out to be defective then get it replaced as soon as possible.
- Inbound Power Failure
Sometimes the breaker gets tripped and the socket starts malfunctioning. In this case, you have to get in touch with an electrician and get the issue resolved at your earliest.
2. Washer Won’t Agitate
If your washer doesn’t agitate then you need to check the following components.
- Drive Motor
The driving force behind the drive belt is basically the drive motor. If the drive motor fails then the belt won’t rotate and as a result the washer won’t agitate. Thoroughly check the agitator assembly and motor coupling and if any issue is found then get it replaced as soon as possible.
- Drive Belt
Having a faulty drive belt won’t allow the drum to rotate. Consequently, the washer won’t agitate and you will face issues. All you have to do is get the drive belt replaced.
- Door Lock
As soon as you replace the faulty door locks, your washer will start working in normal state.
3. Washer Won’t Drain
If your washer is not draining properly then you can consider the following possible reasons.
- Blocked Coin Trap
Clean the coin trap more often because it can easily get blocked and restrict your washer to drain properly.
- Clogged Drain Pump
A lot of pressure will be put on the drain pump if it is clogged. In case of defectiveness, the pump will not pump the water properly. Make a quick replacement for the faulty components.
- Clogged Drain Hose
The water waste will not be able to pass through if the drain hose is clogged. You need to clear all the possible blockages.
- Faulty Door Switch
Your washer will refuse to spin if the door switch has been damaged. Make sure to get it replaced as soon as possible.
4. Washer Won’t Sense
The washer won’t be able to sense due to the following reasons.
- Stuck Keypad
In order for your washer to operate smoothly, unstick the keypad.
- Clogged Drains
Your washer will run smoothly and normally once the drains are unclogged properly.
- Wrong Setting
Always choose the right settings if you want your washer to operate smoothly.
- Reduced Water Level
Make sure that the water pressure is adequate enough for the washer to receive water.
- Other Components
Replace all the faulty components including main control, faulty timer, water inlet valve and water level sensor at your earliest.
5. Washer Won’t Spin Fast Enough
The washer might not spin fast enough due to the following reasons.
- Poor Drainage
The spin rate will eventually increase once the drainage is unclogged.
- Laundry Overload
Presence of extra laundry will make the spinner speed slow. Make sure to keep the laundry balanced.
- Faulty Water Level Switch
Inspect the water level switch using a multimeter. You need to make a quick replacement if no continuity is shown.
- Defective Drive Belt
In case of a loose or faulty drive belt the spin rate of your washer will become extremely slow. Make sure to make a quick replacement.
- Faulty Lid
A faulty lid will not allow your washer to run at the maximum speed. Make sure to replace the faulty components at your earliest.
6. Washer Won’t Fill
Look into the following components if your washer stops filling.
- Faulty Water Inlet Valve
The purpose of a water inlet valve is that it will prevent the water pressure from rising.
- Low Water Pressure
Make sure to measure the pressure using a pressure gauge and adjust it to 20 PSI otherwise your washer won’t fill.
7. Washer Stopped Working Mid-Cycle
Check the following components if your washer stops spinning mid-cycle.
- Defective Water Inlet Valve
Replace the defective water inlet valve with a new one.
- Faulty Door Lock
Replace the old lock with a new one so that your washer doesn’t stop mid-cycle.
- Faulty Main Control
If everything else is working just fine then all you need to do is check the main control and get it replaced if it becomes faulty.
8. Washer Won’t Wash
In case your washer isn’t performing required washing, you need to check the following.
- Damaged Timer
Having a damaged timer means that the motor will be prevented from turning. Make sure to get it replaced.
- Damaged Drive Belt
A damaged drive belt will not allow the washer to spin, wash and agitate. You need to get it replaced as soon as possible.
- Faulty Cycle Selector
A faulty cycle selector will also not allow the motor to turn. The only possible solution is to get it replaced.
- Damaged Water Level Switch
The water level will remain uncontrolled when there is a faulty water-level switch present. Replace the old switch with a new one.
Also Check More Washer:
GE vs Whirlpool Washing Machine [Which One Is Best in 2024]
Washing Machine Drain Pipe Height [Explained Correct 2024]
How Fast Does a Washing Machine Spin? [Explained 2024]
Maytag Centennial Washer Stuck on Sensing [6 Fixation 2024]
Whirlpool Washer Stuck on Sensing [5 Fixations 2024]
Maytag Bravos MCT Washer Diagnostic Mode [Fixations 2024]
Maytag Bravos MCT Washer Reset [4 Ways of Fixations in 2024]
9. Washer Won’t Spin Clothes Dry
If your washer isn’t spinning clothes dry then you need to look into the following things.
- Power Failure
In case of a power failure you need to perform a reset.
- Unbalanced Laundry
Ensure that the loaded laundry present is stable otherwise your clothes will remain wet at the end of the cycle.
- Unlevelled Washer
Place your washer on the ground level.
- Incorrect Spin Selection
Always choose the spin cycle that matches with your laundry.
10. Clogged Fabric Dispenser
If the fabric dispensers have become clogged then the fabric softener dispenser might not work. The fabric residues remain left in the dispenser cup making it clogged. You need to clean the dispenser with hot water and then allow it to dry for some time.
How to Enter Diagnostic Mode?
To enter the diagnostic mode, follow the below mentioned steps.
- Plug in the washer
- Turn the cycle selector knob in the clockwise direction three times
- You will successfully enter the diagnostic mode when the indicator lights up
How to Reset the Washer?
Perform the following steps in order to reset your washer.
- Make sure to unplug the washer
- Wait for around 30 minutes
- Re-plug the washer and see whether the problem still exists or not
The End
I have provided you with all the problems that you might face while using a Maytag Bravos MCT Washer. Along with the problems I have also mentioned the relevant fixes so that you can immediately apply them and get rid of the problems.