Diagnostic mode is really helpful when it comes to the working of components. You can have a surety whether the components are working fine or not by entering into the diagnostic mode. You don’t have to call any technician or expert to have this test done as it is simple and can be performed without any inconvenience. You just have to be sure how to perform the test and that’s it.
Types of Maytag Bravos MCT Washer Diagnostic Mode:
There are two types of Diagnostic Test Modes:
- Automatic Diagnostic Test Mode
- Manual Diagnostic Test Mode
How to Enter Automatic Diagnostic Test Mode?
To enter the automatic diagnostic test mode, you need to follow the below mentioned steps.
- The washing machine should be plugged in and in the standby mode.
- Other than Power, Start or Stop, choose any button and press it for 3 seconds. Release the button and wait for 3 seconds then again press the button for 3 seconds. Repeat this step one more time.
- If the process is successful then you will enter the diagnostic mode. To make a confirmation regarding this notice that the indicator lights will glow for 5 seconds and there will be 88 present on the time display.
- In case you are unable to enter the diagnostic mode, press the power button and make sure that the button you are currently using works properly. If the chosen button is unresponsive then select any other button.
| Two Digit Code | Machine Operation |
| C0 | Slow spin to 23 rpm |
| C1 | Hot and cold primary water valves open along with detergent and fresh fill valves, then the fresh valve until the basket floats, disengaging from the basket hub. The washer will continue filling through the detergent and fresh valves to the minimum water level. |
| C2 | The cold water valve and the bleach valve open for 10 seconds. |
| C3 | Hot water and fabric softener valves are opened for 10 seconds. |
| C4 | Hot and cold primary water valves open along with detergent water valve for 10 seconds |
| C5 | The washing machine will agitate for 15 seconds. |
| C6 | The washing machine’s recirculation pump will energize for 10 seconds |
| C7 | The washing machine’s drain pump is energized until the inner wash basket reengages with the basket hub plus an extra 10 seconds timed drain. |
| C8 | The washer will continue to drain and slow spin at 23 rpm |
| C9 | The inner wash basket should coast to a stop. |
How do I Clear the Error Code on my Maytag Bravos washer?
How to Enter Manual Diagnostic Test Mode?
To enter the manual diagnostic test mode, you need to follow the below mentioned steps.
- Perform the same step 1 and step 2 of the Automatic Diagnostic Test Mode.
- Press the same button one more time while 88 is being displayed on the washing machine for 5 seconds.
- If you want to exit the diagnostic mode then you need to simply press the STOP or POWER button.
- In case of success, you will hear a single beep along with a 2 digit console ID. It will be displayed for 3 seconds followed by 00 and you will also notice “Add a garment” indicator light flashing.
- Replace the user interface if you are unable to get your hands on the 2 digit console ID.
Water Level Sensor Calibration
To recalibrate the water level sensor you need to keep pressing Cycle Signal Button until you hear a single beep sound. “Pt” should be displayed on the display screen for zero calibration.
Water Valves
- Select a particular cycle setting.
- Press the Start button to test if the secondary dispenser valve is working fine or not.
- To turn OFF the valve, press the Start button again.
- Press the Wash/Rinse Temp selection button to energize the primary hot and cold water valves.
- The appropriate water valve will open for your selection.
- Cold + Start = Opens the cold valve.
- Warm + Start = Opens the both hot and cold valves.
- Hot + Start = Opens the hot valve.
Recirculation and Drain Pump Tests
- To activate the Recirculation Pump you need to press and release the “Clean Washer” or “Drain and Spin” button.
OR
- Select the “Clean Washer” or “Drain and Spin” cycle option and press start.
- Press the “Clean Washer” or “Drain and Spin” button one more time to turn the recirculation pump off.
- Press the “Clean Washer”, “Drain and Spin” or “Start” button one more time to turn on the drain pump.
- Press the “Clean Washer”, “Drain and Spin” or “Start” button one more time to turn the drain pump off.
Lid Switch Test
- If you open the machine’s lid then it will cause “Clothes Clean” or “Done” indicator lights to turn ON.
- If you want these lights to be turned OFF then close the lid properly.
Lid Lock Test
- Press and release the “2nd Rinse” or “Extra Rinse” button to lock the lid.
- You will see Door Lock Light flashing.
- Press and release the “2nd Rinse” or “Extra Rinse” button again to unlock the lid.
Motor Tests
Your wash plate or agitator vanes should be covered by water to allow the inner basket to float and disengage from the basket hub. This will be beneficial for motor tests. If your motor tests fail then the reason is most probably related to something lodged between the inner and outer wash basket creating bad wire connections, control problems and friction.
Rotor Position Sensor
The presence of three rinse and spin indicators is beneficial for detecting the three rotor position sensors located on the washer’s motor stator. The inner wash basket rotates with the rotor. What you can do is lift the lid and rotate the inner tub manually. The three lights indicate that the sensor is working correctly.
Agitate
To manually start the agitation press and release the “Soil Level” button once if you want to have a gentle wash action, twice if you want to have a normal action, thrice if you want to have the heavy wash action and four times if you want to turn off the motor.
Check More Washer Fixation:
Whirlpool Washer Stuck on Sensing
Frequently Asked Questions
Q – How do you clear the error code on a Maytag Bravos washer?
A – Press the Start/Pause button once to clear the code. Again press the Start/Pause button to restart the washer.
Q – What is the most common problem with a Maytag washer?
A – Even the most dependable washers, though, can have problems. Maytag washers in particular are prone to a variety of issues. Leaks, uneven loads, and broken spin cycles are a few examples. Thankfully, a lot of these washer issues may be resolved on your own without hiring a specialist.
Q – Is there a reset on the Maytag Bravos washer?
A – No, there is no reset on the Maytag Bravos washer.
The End
So now you understand why it is important to know how to enter into the Diagnostic mode of your washer. Instead of paying large fee amounts to professionals you can try the tests at home and figure out what is wrong with the washer.