Sometimes, the most common solution to any problem is a simple reset. Instead of trying something else, what you need to do is perform a reset and you will be good to go. However, this is not always workable because the issue could be severe sometime. In this case, the reset method won’t work. You need to adopt other solution methods for it.
Well, don’t worry if all these things don’t make sense right now. I will be guiding you thoroughly about each and every possibility. But for now our main focus would be on resetting a Maytag Bravos washer. If you are also its user then make sure to keep reading this article till the end in order to find out more.
How to Reset Maytag Bravos Washer Types of Reset Methods
If you are thinking that there is only one reset method then you are wrong here. There are different types of reset methods available for you to try. Moreover, it doesn’t matter which Maytag Bravos model you own, these reset methods will work for each and every model. I will be providing sufficient details regarding each reset method.
1. Basic Reset
Simple or basic reset is the first type of reset to talk about. This is the most important and easy reset process to carry out. You can expect issues like washer not starting or not changing its cycle to be resolved by this type of reset. If you are willing to try out this reset method then follow the below mentioned steps.
- Switch OFF the main power
- Unplug your Maytag Bravos Washer
- Wait for 5 minutes
- Re-plug the washer after waiting for this duration
- Now turn ON the power
- Run a test cycle to check whether the washer is working or not
After performing this reset method, if the issue still exists then you can try the other reset method which I will be mentioning after this.
2. Procedural Reset
If you ask me which is the most effective reset method then I would say this one. To carry out this type of reset method you need to perform the following steps.
- Make sure your washer is powered ON
- Now press the “Power” or “Cancel” button as per your washer model
- This will allow you to select your preferred wash cycle
- Press “Start/Pause” button to start the reset process
Unfortunately, if this reset method doesn’t work out for you then you need to jump on to the next reset method.
3. Calibration Technique
Calibration technique method is more efficient than the procedural method. If you want to try this one out then make sure to follow the below mentioned steps.
- Empty the washer drum
- Drain out the water from the washer properly
- Keep the lid properly closed
- Keep your washer on standby mode
- Rotate the cycle-selector knob once in the clockwise direction
- Then rotate the cycle-selector knob in the anti-clockwise direction thrice
- Repeat both the movements one time in sequence
- Make sure to continue with the clicking as long as the lights don’t blink
- After you see “Rinse-only” light blinking, stop the clicking
- In order to complete the reset process, press “Start”
After carrying out this process, make sure to check whether the error still exists or not.
4. 12’O Clock Turn
This technique might sound weird at first but trust me it comes in handy when no other technique does. So in order to carry out this method, you need to follow the below mentioned steps.
- Turn your washer ON
- Turn the cycle-selector knob and bring it in a 12’O Clock position
- Then turn the knob thrice in clockwise direction
- Turn the knob in anti-clockwise direction once and then in clockwise direction
- Carefully observe whether any light flashes or not
- In case it does, turn the knob in clockwise direction for four times
- Press “Start” as soon as the light flashes
That’s it, this method involves only these steps.
IMPORTANT
It is important to note that before carrying out any reset method, it is important to know about the precautionary steps. Make sure the following conditions are checked before performing any reset method.
- The washer drum should be empty
- The lid should be properly closed
- The washer should be on standby mode
Which Issues are resolved by Reset Methods?
You can expect the following issues to go away by carrying out the reset methods which I have mentioned above.
- Error codes
- No agitation
- Faulty lid lock
- Washer won’t start
- Continuous spinning
- Strange noises
- Continuous vibration
- Washer won’t change cycle
- Lid switch failure
- Power disturbance
- Replacing control board
Use of Diagnostic Mode
As mentioned before, not all issues can be resolved by performing the reset methods. Some of them require a different troubleshooting method in order to get resolved. For this situation, diagnostic mode comes in handy. You can make your washer enter the diagnostic mode and if there is any error then it will come to the surface. Once this is done, you can use that error code in order to get the issue resolved properly. If you want your washer to enter the diagnostic mode, then follow the below mentioned steps.
- Turn the cycle-selector knob in clockwise direction only once
- Wait for 0.5 seconds
- After waiting for this duration, repeat the above step again
- Repeat the above step again for third time as well after waiting for 0.5 seconds
- You need to keep repeating this step until you see the lights blinking
Once your washer enters the diagnostic mode, you will know about the underlying errors. This will make the troubleshooting process easier for you.
Also Check More Washer:
GE Washer Not Spinning Clothes Dry [6 Fixations]
Kenmore Washer Not Spinning Clothes Dry [6 Fixation 2024]
GE vs Samsung Washer [Comparison Which One Is Better 2024]
GE vs LG Washer [Comparison Which One is Better?] 2024
Maytag Bravos MCT Washer Problems [Fixation 2024]
GE vs Whirlpool Washing Machine [Which One Is Best in 2024]
Washing Machine Drain Pipe Height [Explained Correct 2024]
How Fast Does a Washing Machine Spin? [Explained 2024]
Frequently Asked Questions
Q – How do I clear my Maytag code?
A – You will have to press the Pause/Cancel button twice while the Power button once in order to clear the Maytag codes.
Q – What is a control lock on a Maytag washer?
A – If your Maytag washer has control lock activated then it means the control will not work. You will witness “LoC” or “LC” whenever you try to press any button on the control.
Q – Why is my Maytag washer stuck on lock?
A – Maytag might be stuck on lock when either the unit took too long to fill with water or when there is a glitch in the electrical parts of the washer.
Wrap Up
To put it briefly, I have gone over every method that could assist you in performing a reset. When it comes to Maytag Bravos washers, there are essentially four main reset techniques. The list includes every option, ranging from the most simple to the most effective. Whichever option you choose at this point is up to you. Furthermore, a single reset technique can fix certain problems while a different way can fix others.