Not everyone is a fan of interruptions. People mostly like their tasks to be done in a continuous manner. However, it isn’t always the tasks, sometimes it is the appliances we are talking about. It happens most of the time that when we are using any appliance we want it to work smoothly without any interruptions.
People have been talking about this issue since their Bosch dishwasher starts and then stops working. It happened so frequently that they got fed up and started complaining about it. If you are also one of them then you don’t need to worry as I will be explaining various troubleshooting methods to get rid of this issue.
Bosch Dishwasher Starts then Stops – What are the Reasons?
Following are some of the common reasons due to which Bosch dishwasher starts and then stops.
- Blown thermal fuse
- Faulty door latch
- Malfunctioning control board
- Faulty pump
- Damaged motor
Bosch Dishwasher Starts then Stops – Troubleshooting Methods
Don’t think that your Bosch dishwasher will simply start and then stop. In fact, this problem can occur in multiple natures. So if your dishwasher:
- Starts and then stops repeatedly
- Stops during the cycle
- Stops 3 minutes in the middle of the wash cycle
- Starts, stops, beeps, fills and stops
- Drains and then stops
All in all, if you have come across any of the above mentioned situations then I encourage you to keep reading this article till the end in order to have this issue resolved. Although the nature of the problems is different, their troubleshooting is somehow the same.
1. Bosch Dishwasher Starts then Stops
If the fuse present in your dishwasher has blown then there are high chances that your dishwasher will stop working and won’t start again. Moreover, a thermal fuse can also be the reason for your non-workable dishwasher. Whenever your dishwasher experiences some sort of overheating, the thermal fuse will definitely become faulty and stop working. In order to protect the unit from severe damage, the circuit breaker trips.
Solution
Make a confirmation that the fuse has become faulty. If so, you need to make a quick replacement of the thermal fuse with a new one. Also check the breaker whether it has been tripped or not. If it has been tripped, turn it back ON.
2. Bosch Dishwasher Stops Mid-Cycle and Beeps
It is not at all recommended to open the unit’s door while the wash cycle has been going on. Doing this will definitely bring interruption in the wash cycle. Consequently, the wash cycle will start and then stop for 3 minutes.
What about when you haven’t opened the door mid-cycle but still the cycle stopped? One of the most common reasons for this could be the presence of a faulty door latch. The dishwasher will misinterpret the closed door for an open one.
Solution
It is obviously common to not open the unit’s door between the cycles. Secondly, if the door latch has become faulty then you need to use a new one. If you are replacing the door latch on your own then I suggest you consider the following precautionary steps.
- Unplug the appliance
- Check the breaker, trip it
- Stop the water supply by using a shut-off valve present under the sink
- Remove the water supply lines
- Remove the unit by unscrewing the nuts
- Slightly remove the unit
How to Replace the Latch?
- Remove the panel present in front of the door switch
- Test the switch using a multimeter
- Replace your old latch with a new one
How to Reset the Dishwasher?
Before diving into expensive fixes, it is better to reset your dishwasher as it resolves many underlying issues. Resetting your dishwasher will surely resolve many bugs. However, if you don’t know how to perform a reset then keep following the below mentioned steps.
- Keep holding the “Start” button until the display goes off
- Wait for the water to completely drain out
- Start the cycle again
- Press “Power” and “Start” buttons simultaneously
- Repeat the above step again
- Unplug the unit from the power supply
- Wait for a few minutes before plugging it back
Following these steps will allow your dishwasher to undergo a reset.
3. Bosch Dishwasher Starts to Drain then Stops
Your dishwasher has a drain pump present in it, one end of the hose is attached to the sink’s garbage disposal while the other end is attached to the pump. Try out the following if the draining isn’t working properly.
Check for Clogs in the Air Gap
- Find the air gap present at the back of your sink
- Manually remove the cap
- Clean the material properly and remove all the possible debris
Check for Clogs in the Drain Hose
- Disconnect the drain hose and air gap
- Check the hose clogging by draining the water
- Start a rinse wash cycle to check for possible blockages
- Remove these blockages using a plumbing device
Check the Filters
It is very essential to check the filters for possible blockages and clogging. A filter might have food particles left within them that could greatly affect the draining. Before diving into expensive solutions, it is important to check your filters first. If they are dirty, clean them and if they have completed their life then make sure to replace them.
Also Check More Dishwasher:
Bosch Dishwasher Cant Change Cycle [5 Fixations 2024]
Bosch Silence Plus 44 dba Troubleshooting (9 Solution 2024)
Why is my Kitchen Aid Dishwasher Beeping? [10 Fixation 2024]
Bosch Dishwasher Cycles Explained [8 Types Cycle 2024]
GE Dishwasher Start Button Not Working [10 Fixations 2024]
Whirlpool Dishwasher Fills with Water then Stops 4 Fixation
4. Bosch Dishwasher Starts to Fill then Stops
In case your dishwasher is filling with water but then stopping eventually is due to the presence of a faulty thermal fuse. This component comes in handy as it protects the circuit board of the unit. Make sure there aren’t any possibilities of a faulty thermal fuse.
The End:
In a nutshell, I have shed light on all the possibilities due to which you might be experiencing this issue. There is nothing to worry about as this is not something very serious. If you take the right steps and actions then I assure you that you will get rid of this issue within no time. Keep following this article thoroughly so you can avoid future inconveniences.